The writer is making a few good points relating to Tools You Need to Install a New Bathtub overall in this article just below.
Setting up a bath tub isn't precisely rocket science, yet it does require strong plumbing, carpentry, and sometimes, tiling abilities. Replacing an old bath tub with a new one is additionally a moderately difficult job. If the old tub is easily accessible, the task can move easily; if you have to open up a wall to get rid of the old tub and also position the brand-new bathtub, the job is a lot harder. In either case, the job is within a home handyman's abilities, although you will need an assistant to leave the old bathtub and embeded in the new one. Make certain you have actually qualified on your own for the job as well as fit attempting it. Instead of hiring a specialist to take control of a halfway-completed job, it is far better to consider utilizing one prior to you begin. Possibilities are you might need an expert plumber to make tube links.
This article will aid you install a new bath tub in your bathroom if you have currently acquired a new tub and also do not need to alter the setup of your previous water supply pipes.
Your devices and also material checklist must consist of the following:
Removing Old Taps
If you need to change old faucets with new ones as a part of your installation, after that the first thing you need to do is disconnect the supply of water. After doing so, switch on the faucets to drain pipes any water remaining in the system. The process of eliminating the existing faucets can be fairly bothersome due to the restricted gain access to that is commonly the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipes to the faucets. Have a fabric all set for the continuing to be water that will certainly originate from the pipes. Once the supply pipes have been removed, make use of the same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single taps from turning during this process. Once the taps have been removed, the holes in the bath/basin will need to be cleansed of any kind of old sealing compound.
Before proceeding to fit the new taps, contrast the pipeline connections on the old taps to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the new taps to fit.
Fitting New Taps
If the tails of the new taps are plastic, after that you will certainly require a plastic port to avoid damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end supplies a link to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly need minimizing couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, position the tap in the installing hole in the bath/basin guaranteeing that the washers remain in area in between the faucet as well as the sink. Protect the tap in place with the manufacturer provided backnut. Once the faucet is firmly in position, the supply pipelines can be linked to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with regular faucet ports. The former kind must be linked to the tap ends initially, tightening up only by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have been connected.
Mounting the Bath tub
Utilizing the two wooden boards under its feet, position the tub in the needed position. The wood boards are helpful in equally spreading out the weight of the tub over the area of the boards as opposed to concentrating all the weight onto four small factors.
The following goal is to ensure that the bath tub is leveled all round. This can be accomplished by checking the spirit level and also changing the feet on the bathtub till the level reads degree.
To set up taps, fit all-time low of the outermost flexible faucet port to the appropriate supply pipeline by making a compression join; then do the very same for the other tap.
Turn on the supply of water and inspect all joints and brand-new pipework for leakages and tighten them if needed. Fill the bath tub and likewise check the overflow electrical outlet and the typical electrical outlet for leaks.
Ultimately, repair the bathroom paneling as described in the maker's instruction manual. Tiling as well as securing around the tub needs to wait until the tub has been utilized at the very least once as this will certainly settle it into its final placement.
Preparing for the Installation
First of all, the sustaining frame supplied with the bathroom needs to be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is essential to ensure that if the faucet features a plastic washer, it is fitted between the bathroom and also the taps. On a plastic bath, it is additionally sensible to fit a supporting plate under the faucets device to prevent strain on the tub.
Fit the adaptable tap connectors to the bottom of the two faucets making use of 2 nuts and olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet via the hole in the bath. Use the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. Make certain you utilize every one of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom need to currently prepare to be fitted in its final position.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is required to secure the joins with a silicone rubber caulking. This is essential as the fitting can move enough to break a stiff seal, triggering the water to permeate the wall between the bath and the tiling, resulting in problems with dampness and possible leaks to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your fixtures as well as fittings. They are sold in tubes and cartridges, and can securing spaces as much as a width of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of drenched newspaper or soft rope. Remember to always load the bath tub with water prior to sealing, to allow for the movement experienced when the bathtub remains in use. The sealant can crack rather very early if you do not take into consideration this motion before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally conveniently offered on the market. It is advisable to fit the floor tiles utilizing water-resistant or waterproof glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you really like more info about Installing A Bathtub? Leave a remark down below. We would be delighted to see your suggestions about this content. We are looking forward that you visit us again before long. Remember to take the time to share this page if you appreciated it. Many thanks for taking the time to read it.
Browse Our Site